Share this Job

Apprentice Simulator Technician

Date: Aug 8, 2019

Location: Wichita, KS, US, 67209

Company: FlightSafety International

Requisition 13325

SUPERVISORY RESPONSIBILITIES:

None

QUALIFICATION REQUIREMENTS: (The requirements listed below are representative of the knowledge, skill and/or ability required.)

EDUCATION AND/OR EXPERIENCE: (Minimum Requirements)

Apprentice Associate's degree in electronics from college or completion of an electronics technical school preferred; or a combination of three (3) years’ education and experience, including:

• Electronics technology, avionics or related civilian/military technology; or

• Equivalent direct experience with simulators or other FTDs

Tech I - Associate's degree in electronics from a college or completion of a civilian/military electronics technical school preferred, plus two (2) years experience, including:

• Electronics technology, avionics or related civilian/military technology; or

• Equivalent direct experience with simulators or other FTDs

Must be able to:

• Read and interpret technical drawings

• Use test equipment, support equipment and tools used on flight simulators, graphical flight simulators (GFSs) and associated electronics devices

• Demonstrate a good understanding of the advanced operating principles of simulator and FTD subsystems.

 

Education can be substituted by a combination of three (3) years education and experience in a related field.

Tech II - Associate's degree in electronics from a college or completion of a civilian/military electronics technical school preferred, plus four (4) years experience, including:

• Electronics technology, avionics or related civilian/military technology; or

• Equivalent direct experience with simulators or other FTDs

Must be able to:

• Read and interpret technical drawings

• Use test equipment, support equipment and tools used on flight simulators, graphical flight simulators (GFSs) and associated electronics devices

 

Education can be substituted by a combination of three (3) years education and experience in a related field.

Created: 5/16 Revised: 3-14-17, 7-25-18

LC FTD

Grade: 9, 12, 13, 15

Date: 7-25-18

4 of 5

FlightSafety International Proprietary Information. All rights reserved.

Tech III - Associate's degree in electronics from a college or completion of a civilian/military electronics technical school preferred, plus Seven (7) years experience, including:

• Electronics technology, avionics or related civilian/military technology; or

• Equivalent direct experience with simulators or other FTDs

Must be able to:

• Read and interpret technical drawings

• Use test equipment, support equipment and tools used on flight simulators, graphical flight simulators (GFSs) and associated electronics devices

Education can be substituted by a combination of three (3) years education and experience in a related field.

SOFTWARE KNOWLEDGE AND SKILLS:

General knowledge of Microsoft word, excel, PowerPoint, and Outlook required. Familiarity with Microsoft Access preferred. Knowledge of other software programs may be required, as needed.

EQUIPMENT KNOWLEDGE AND SKILLS:

PC literate and Basic Office equipment

OTHER SKILLS AND ABILITIES:

Fluency in English, through both verbal and written communications; Able to read and interpret documents: Able to write routine reports and correspondence.

Must be customer oriented with mature interpersonal skills projecting a friendly, cooperative manner accompanied by good grooming habits and adherence to FlightSafety International specified dress code standards.

REASONING ABILITY:

Able to solve practical problems and deal with a variety of concrete variables in situations where only limited standardization exists; Able to interpret a variety of instructions furnished in written, oral, diagram, or schedule form.

CERTIFICATES, LICENSES OR REGISTRATIONS:

Valid Driver’s License, where applicable.

PHYSICAL DEMANDS AND WORK ENVIRONMENT: The physical demands and work environment described here are representative of those that must be met and/or encountered by an employee to successfully perform the essential functions of this job. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions.

Created: 5/16 Revised: 3-14-17, 7-25-18

LC FTD

Grade: 9, 12, 13, 15

Date: 7-25-18

5 of 5

FlightSafety International Proprietary Information. All rights reserved.

While performing the duties of this Job, the employee is regularly required to sit and talk or hear. The employee is frequently required to stand; walk; use hands to finger, handle, or feel and reach with hands and arms. The employee is occasionally required to climb or balance and stoop, kneel, crouch, or crawl.

The employee must frequently lift and/or move up to 10 pounds and occasionally lift and/or move up to 40 pounds. Specific vision abilities required by this job include close vision, distance vision, color vision, peripheral vision, depth perception and ability to adjust focus.

The noise level in the work environment is usually moderate.

The below statements are intended to describe the general nature and level of work performed by employees assigned to this classification. They are not intended to be construed as an exhaustive list of all responsibilities, duties and skills required of personnel so classified. Nothing in this job description restricts management’s rights to assign or reassign duties and responsibilities to this job at any time. This job description is not an employment agreement or contract. Management has the exclusive right to alter this job description at any time without notice. BASIC FUNCTION:

The Mechanic/Machinist makes, as required, mechanical and machined modifications, updates, and repairs to enhance the performance of Flight Training Device(s) and other associated equipment utilized by FlightSafety International by performing the following duties.


 

FlightSafety is an Equal Opportunity Employer/Vet/Disabled.


Nearest Major Market: Wichita

Find similar jobs: